CGI Door Installation Nationwide | TruePane Windows & Doors

CGI Door Installation: The Miami Owner’s Guide

CGI door installation in Miami typically runs $1,800 to $4,600 installed, depending on the door’s size, series, and whether the frame needs work. We stock CGI-compatible hinges, rollers, weatherstripping, track kits, and lock hardware on our trucks, and in most cases the work is completed in a single visit. Most homeowners find us the same way: the door has been dragging for months, a hinge pin finally gave out in July heat, or the aftermath of a storm exposed a seal that was already failing.

Call (561) 956-2754

Dale Kessler has installed and serviced CGI doors across the Miami metro for over a decade, from Coconut Grove bungalows to high-rises off Brickell. What we’ve learned is that CGI doors rarely fail all at once. They give warning. The trick is knowing which warnings matter before the door binds shut or the lock refuses to throw.

Key Takeaways:

• CGI door parts are series-specific. A Westminster hinge is not a Centennial hinge, even if the screw holes look close.
• Miami’s salt air and humidity kill weatherstripping years faster than the manufacturer’s average lifespan suggests.
• We stock OEM CGI hardware on our trucks and install it same-day in most cases.
• Both warranty layers get registered in writing before the truck leaves your driveway.

Which CGI Models This Applies To

We install and service door hardware across CGI’s residential lines: the Sentinel series, Estate Collection, Targa, and the newer CGI 900 Series. We also work regularly on CGI’s impact-rated doors paired with their WindowsMax and Estate windows, so if your home already has a CGI system, the door is part of that package.

Here’s the compatibility gotcha most people don’t know: CGI changes hinge geometry and roller specs between series and sometimes between model years within the same series. A hinge that fits a 2016 Sentinel will not necessarily fit a 2021 Sentinel. The manufacturer stamps a series code and production date on the door’s edge label, near the hinge side. That label, plus the door’s width and weight, is what we use to confirm the right hardware before any cutting or drilling happens.

OEM versus aftermarket is a real decision on CGI doors. Aftermarket hinges and rollers can be half the price, but the metallurgy and plating often are not rated for Miami’s coastal corrosion. CGI’s stainless steel hardware is typically 316 alloy on hinge pins and rollers. Cheaper aftermarket parts often use 304 or zinc-plated steel, which pits and binds in two or three seasons. For a door that is supposed to protect the house through a hurricane, we recommend OEM. We quote both options on paper so the homeowner sees exactly what they are buying, side by side.

Signs Your CGI Door Installation Is Failing

• The door drags or scrapes the threshold. Usually a worn roller or a hinge pin that has egged out the hinge leaf. On CGI doors, the bottom roller takes the most load and is almost always the first to go. When the door drags, the track is also wearing, so delaying the repair turns a $200 roller replacement into a $600 track job.
• The lock won’t throw without lifting or pulling the door. This means the door has settled enough to shift the strike plate alignment. On an impact-rated door, a misaligned lock is more than an inconvenience; it weakens the door’s ability to hold its seal when wind pressure hits. Miami sees that wind pressure every hurricane season.
• The weatherstripping looks compressed, torn, or gone in spots. Salt air and sun do this faster here than anywhere else in the country. A compromised seal lets water and warm air in, and on a CGI door the seal is part of the impact system’s water barrier.
• The door squeals or groans when it moves. Hinge pins and roller bearings lose lubrication and corrode from the inside. A little silicone spray may quiet it for a week, but if the sound comes back, the bearing itself is done.
• The door sits visibly out of level or the gap between panel and frame changes with the seasons. This can be frame settlement or hinge leaf wear. Either way, a door that shifts with the weather is a door that will not hold its Miami-Dade wind rating when it matters.

Replacement Cost & What’s Included

Installed CGI door hardware in Miami falls into three rough ranges. A roller and hinge replacement runs $180 to $500 depending on how many points need work. A full hardware package (hinges, rollers, weatherstripping, lock hardware, and track adjustment) typically runs $700 to $1,400. A complete door replacement, when the panel or frame is too far gone, lands between $2,200 and $4,600 installed, including old door removal and haul-away.

Every quote includes the parts, the labor, the setup, and a written line-item breakdown. No surprise charges appear later. If we open the door and find something else worn, we stop, show you, and quote the additional work before doing it.

Our workmanship is guaranteed for 90 days under the Done Right Promise. If it’s not right, we come back and make it right, no paperwork fight. The manufacturer warranty layers get registered in writing with the durations stated before we leave the driveway.

DIY or Call Us?

What you can safely do: check the edge label for the series and production date, note which corner of the door is dragging, and inspect the weatherstripping for visible tears. That information helps us quote accurately over the phone.

Here’s where DIY goes wrong. CGI doors are heavy, often 150 to 250 pounds depending on size and glass. Pulling the door off its track to swap a hinge or roller without the right support risks the panel dropping, which can shatter laminated impact glass, crush fingers, or both. The springs and track on a CGI door are not under garage-door-style tension, but the panel weight itself is serious. We’ve repaired more than one door where a well-meaning homeowner cracked the corner of the panel by resting it on concrete and applying pressure the wrong way.

It’s honest to say that checking and reporting symptoms is a homeowner’s job. The repair on a heavy impact door is a technician’s job. If you think the door is failing, call (561) 956-2754 and tell us what you’re seeing. We’ll give you a straight answer, not a sales pitch.

FAQs